Before you commit volume, the same few questions come up every time. The answers below are written from your side of the table: what to verify, what to ask for, and what the number on a website actually proves. For anything specific to your drawing, email [email protected].
What is a traceability chain, in plain terms?
A traceability chain is the record that ties a part back to its origin: raw material source and usage, process parameters, machine data, production batch, machining time, operator, and inspection results. When a problem surfaces, the chain points to the exact lot instead of guessing.
Why should I care about traceability on my parts?
Because every process produces a non-conformance eventually, and the cost depends on how precisely you can find it. Traceability turns a full recall into an isolated rework, and a vague answer into a precise one about which lot, machine, and operator.
How far back can you trace my specific part?
The MES/ERP system records the full chain on every lot: raw material source and usage, process parameters, equipment running data, production batch, machining time, operator, and inspection results — from the door to the finished part.
How do you verify the raw material is what I specified?
Every incoming lot is XRF-checked against its mill certificate before it reaches a machine, so the raw material link in the chain is verified, not just recorded. A substituted alloy is caught at the door, before it enters the chain.
Is every job traced, or only some?
Yes. The traceability chain runs on every job, not just automotive or regulated ones. The discipline you need for a recall is not reserved for the customers who audit — it is the default on every lot.
How does traceability help during an audit?
An auditor asks to see the chain, not hear about it. The MES/ERP record shows raw material, process, machine, batch, operator, and inspection per lot, so the traceability can be demonstrated on demand rather than described.
How does traceability turn a failure into an isolated event?
When a non-conformance surfaces, the chain gives the answer in one query: which lot, machine, operator, and raw material. The affected lot is quarantined, and the rest of the run keeps its value and schedule.
What should I ask a supplier about its traceability?
Ask how far back the record goes, whether it is automatic or assembled on request, and whether they can pull up a real lot and show the chain. A supplier that answers all three with the record in front of them is one whose traceability you can trust.
Which materials and industries do you cover?
We machine aluminum, stainless steel, titanium, brass, copper, and Inconel, plus engineering plastics including PEEK and Delrin. These custom machined parts go into medical, aerospace, automotive, robotics, electronics and defense applications, with the inspection, traceability and documentation each sector requires before it places an order.
What buyers ask most
Three questions come up on nearly every enquiry. What is the minimum order? One piece - a single prototype can be machined, checked and iterated before any volume is committed. What is the lead time? Roughly 3 / 7 / 30 days depending on the material and the documentation scope, from a simple aluminium part to a full first-article package. What tolerances can you hold? ±0.003 mm milled and ±0.002 mm turned, verified on a Hexagon CMM, with Ppk 1.67 or better initial and Cpk 1.33 or better in production on critical characteristics. The answers are short because the capability is specific, not vague.
The answers behind the answers
The plant behind these answers is Dongguan Zhuohang Ltd - 6,800 m² in Hengli Town, Dongguan, 100+ CNC machines including Mazak VARIAXIS I-600 and INTEGREX I-250H S, and certification to ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015 with the certificate numbers published and verifiable. The service area covers Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, with worldwide shipping from Dongguan. Contact Felipe Iglesias at [email protected] or +86 13126536955 with a drawing and a quantity for a specific answer to your specific part.
How to verify the claim in one email
The fastest way to separate a real floor from a brochure is to ask for the machine list and the certificate numbers - and this facility answers in one email. Dongguan Zhuohang Ltd operates 100+ CNC machines across 6,800 m² in Hengli Town, Dongguan: Mazak VARIAXIS I-600 five-axis, INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes. Inspection is on a Hexagon CMM with the 10:1 gauge rule, certification is to ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015, and critical characteristics run at Ppk 1.67 initial and Cpk 1.33 in production.
Worldwide buyers across Europe, the Americas, Asia, Oceania and Africa are supplied from Dongguan. MOQ is 1 piece, lead times run roughly 3 / 7 / 30 days, and the quote from Felipe Iglesias ([email protected], +86 13126536955) comes back with the routing and the capability evidence together.
Take the next step
One drawing and one quantity is the whole hand-off. Send a STEP or IGES model and a 2D drawing with the tolerances, datums, material grade and finish, state the quantity and lead time, and the reply is an itemised quote - material, setup, cycle time, inspection - rather than a round number. If the drawing is incomplete, send what you have and the open questions; the point is to open the conversation, not to wait for a perfect package.
Contact Felipe Iglesias at [email protected] or +86 13126536955. MOQ is 1 piece, lead times run about 3 / 7 / 30 days, and the service area covers Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa, shipped worldwide from Dongguan.
Tolerance and surface finish reference
±0.003 mm milled, ±0.002 mm turned, and ±0.002 mm ground or wire-cut, all verified on a Hexagon CMM against the datum scheme. Surface finishes span Ra 0.8 to 3.2 µm as-milled, Ra 0.2 to 0.4 µm ground, and Ra 0.05 to 0.1 µm polished. The 10:1 gauge rule governs every feature - the instrument must resolve ten times finer than the tolerance it checks. And the datum is what makes the tolerance real: read against two different datums, the same callout gives two different parts, so state the datum and the convention, ASME Y14.5 or ISO.
The material decision
Aluminium 6061-T6 leads on light and economical; 7075-T6 adds strength for aerospace and structural parts. In stainless, 303 machines cleanly for fittings, 304 and 316 add corrosion resistance, and 17-4 PH adds strength after ageing. Steel wins on strength and cost. Brass is the fastest metal to machine and conducts well. Copper C110 is the conductivity benchmark, with C145 tellurium copper for machinability. Titanium and Inconel hold high-temperature strength but machine slowly and cost more. The material is the biggest lever on price, so it is selected for the service - load, environment, temperature - not by habit, and the grade is named on the drawing so the mill certificate confirms it.
Placing the part on the right process
The shortest way to a correct part is to let the shop read the drawing and place it on the right machine, because the process follows the geometry, the material and the tolerance - not the label on the page. A part with a turned profile goes to the lathe, a prismatic part to the machining centre, a long thin part to a Swiss machine, and a sheet or panel to the router; you state what the part must do, and the shop matches the process. That is the whole of the routing decision, and it is settled at the quote.
This floor runs 100+ CNC machines - Mazak VARIAXIS I-600 five-axis, Mazak INTEGREX I-250H S mill-turn, Brother SPEEDIO, and TSUGAMI, STAR and CITIZEN Swiss lathes - at ±0.003 mm milled and ±0.002 mm turned, verified on a Hexagon CMM, with certification to ISO 9001:2015, IATF 16949:2016 and ISO 14001:2015. MOQ is 1 piece and lead times run roughly 3 / 7 / 30 days. Send the drawing to Felipe Iglesias at [email protected] or +86 13126536955 and the process is matched to the part.
What this shop actually runs
We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:
- 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Typical work: compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
- 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Typical work: prismatic parts, plates, brackets, housings.
- Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Typical work: long, slender rotational parts at ±0.002 mm.
- CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Typical work: shafts, bushings, flanges up to ±0.002 mm.
- Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Typical work: hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
- Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
- Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.
Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.
Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.
Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.
Contact: Felipe Iglesias, [email protected], +86 13126536955.
Have a traceability question we did not cover?
Send it to [email protected] or call +86 13126536955 — the answer comes with the record behind it.
Frequently Asked Questions
1. What is a traceability chain, in plain terms?
In short, A traceability chain is the record that ties a part back to its origin: raw material source and usage, process parameters, machine data, production batch, machining time, operator, and inspection results. When a problem surfaces, the chain points to the exact lot instead of guessing.
2. Why should I care about traceability on my parts?
In short, Because every process produces a non-conformance eventually, and the cost depends on how precisely you can find it. Traceability turns a full recall into an isolated rework, and a vague answer into a precise one about which lot, machine, and operator.
3. How far back can you trace my specific part?
The MES/ERP system records the full chain on every lot: raw material source and usage, process parameters, equipment running data, production batch, machining time, operator, and inspection results — from the door to the finished part.
4. How do you verify the raw material is what I specified?
Every incoming lot is XRF-checked against its mill certificate before it reaches a machine, so the raw material link in the chain is verified, not just recorded. A substituted alloy is caught at the door, before it enters the chain.
5. Is every job traced, or only some?
Yes. The traceability chain runs on every job, not just automotive or regulated ones. The discipline you need for a recall is not reserved for the customers who audit — it is the default on every lot.
6. How does traceability help during an audit?
An auditor asks to see the chain, not hear about it. The MES/ERP record shows raw material, process, machine, batch, operator, and inspection per lot, so the traceability can be demonstrated on demand rather than described.
7. How does traceability turn a failure into an isolated event?
When a non-conformance surfaces, the chain gives the answer in one query: which lot, machine, operator, and raw material. The affected lot is quarantined, and the rest of the run keeps its value and schedule.
8. What should I ask a supplier about its traceability?
In short, Ask how far back the record goes, whether it is automatic or assembled on request, and whether they can pull up a real lot and show the chain. A supplier that answers all three with the record in front of them is one whose traceability you can trust.
9. Which materials and industries do you cover?
In short, We machine aluminum, stainless steel, titanium, brass, copper, and Inconel, plus engineering plastics including PEEK and Delrin. These custom machined parts go into medical, aerospace, automotive, robotics, electronics and defense applications, with the inspection, traceability and documentation each sector requires before it places an order.
What payment methods and terms do you accept?
PayPal, Western Union, and bank or wire transfer. For long-term customers we also accept Net 30, Net 45, and Net 60 terms after an approved credit review.
What happens if a machined part has a manufacturing defect?
We provide free repair or remake for parts with manufacturing defects. All repair and remake costs, including return and shipping, are on us.
How quickly do you respond to inquiries?
We respond to every inquiry within 24 hours. Quotations for standard parts are returned within 48 hours; print reviews and DFM feedback are usually back within one business day.
Standards referenced on this page
- ASTM B211/B211M-19 — Standard Specification for Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire
- ASTM A276/A276M-17 — Standard Specification for Stainless Steel Bars and Shapes
- IATF 16949:2016 — Automotive quality management system standard
